Bosch Sensortec Community

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    BHI160B ASDA and ASCK requirements

    Benji
    Member

    BHI160B ASDA and ASCK requirements

    TL;DR - even the BHI160B shuttle board 3.0 fails to send interrupts or data after uploading firmware ("firmware/Bosch_PCB_7183_di03_BMI160-7183_di03.2.1.11696_170103.h") and installing virtual sensors (been trying with BHY_VS_ACCELEROMETER) and callbacks when I desolder the BMM150 (but leave the aux pull-up resistors). Is there some MINIMUM bus capacitance needed to slow down the rise/fall times on the ASDA and ASCK lines?

     

    I've been fighting with a custom board using the BHI160B and an ESP32S3 (programmed in Platform.IO with the Arduino framework) for a while. The behavior has been the same, I talk to the chip just fine, upload firmware just fine, install virtual sensors and callbacks just fine, but I only ever get an interrupt after firmware upload.

    I ended up buying the shuttleboard to isolate my problem, and it immediately worked. Both with the stand-alone firmware and accelerometer virtual sensor, and with the BHI+BMM firmware and orientation virtual sensor. I don't have a BMM150 on my custom board so I desoldered it from the shuttle board and suddenly it started having identical behavior. I tried to add 10pf capacitors to the ASDA and ASCK lines as that is the input capacitance in the BMM150 datasheet but I ripped up a pad on the shuttleboard and so was unsuccessful. I have no other ideas for what could cause the BHI failure using firmware not talking to the BMM150 when the BMM is simply removed.

    4 REPLIES 4
    BSTRobin
    Community Moderator

    Re: BHI160B ASDA and ASCK requirements

    Hi Benji,

    If you didn't use BMM150, you should remove aux pull-up resistors and keep ASCK, ASDA pins floating.

    Benji
    Member

    Re: BHI160B ASDA and ASCK requirements

    fascinating, since the datasheet says exactly the opposite. I'll give it a try and report back.

    Benji_0-1666800213007.png

     

    Benji
    Member

    Re: BHI160B ASDA and ASCK requirements

    No luck, it has the same behavior where I can talk to the BHI hub just fine, but it doesn't seem to get any data from the BMI. 

    Benji
    Member

    Re: BHI160B ASDA and ASCK requirements

    Well, we decided we needed magnetic data as well. Spun up a new board with both the BHI and BMM and it worked straight away. Part of me wants to start desoldering to figure out where the problem was, but alas - it works so I'm moving on.

    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist