Bosch Sensortec Community

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    BMP390 - data is not displayed on Application board3/BMP390 shuttle board and DD2.

    jsayed
    New Poster

    BMP390 - data is not displayed on Application board3/BMP390 shuttle board and DD2.

    Hi guys,

    I am new to this and need some help. Thank you in advance. 

    I have an application board 3.0 (APP3) with a BMP390 Shuttle Board 3.0 on it.

    I have installed Development Desk 2.0 (UI Ver 3.25.0.0) on Windows 10. 

    My App3 is connected to my PC with Windows 10 through a USB cable.

    I can connect to the APP3 and DD2 displays the sensor main menu. (a graph show pressure and temperature)

    But I don't see any sensor output, just shows the main page of the (pressure & temperature) display.

     I have done the following (step by step): still don't see any data.

    a. updated window driver and was able to recognize the USB interface and connect.

    b. update the bootloader from COINES\v2.7.0\firmware\app3.0\bootloader_update.

    c. updated the DelopmentDesktop_2.0_Firmware_v1.9.bin. from COINES directory.

      Still, I don’t see any action from APP3/BMP390. Just an empty main graph table with no data.

     

    Note: I did all this because, when I received the APP3/BMP390 the boards were not showing any data and after all

    With these updates, the situation has not changed.

     

    I am lost and need some help.

    1. Both LEDs on my app3 are lit, orange(good pwr), and RED. is this right?  Should RED be GREEN?

    2. When I try to update flash from DD2 bootloader menu with Blue LED on.

      using DD2 in Boot mode, ‘Setting’ -> ‘Firmware upgrade’ menu. using file

      “DevelopmentDesktop_2.0_frimware_V3.5.fwu2” the system indicate

      “Firmware update in progress...BUT just sits in this position forever, meaning flash

      never completes updating. I have waited 1/2 hour and still no indication of what going on.

      Appreciate any help --- thank you

     

    5 REPLIES 5
    BSTRobin
    Community Moderator

    Re: BMP390 - data is not displayed on Application board3/BMP390 shuttle board and DD2.

    Hi jsayed,

    It is not correct when red LED is on. You can refer "C:\COINES\v2.7.0\doc\BST-DHW-AN013.pdf" document and check if you follow the operation step by step.

    Application 3 board Updating bootloader DD firmware and MTP firmware using coines.png

    jsayed
    New Poster

    Re: BMP390 - data is not displayed on Application board3/BMP390 shuttle board and DD2.

     

    Hi BSTRobin,
     
     
     Thank you for a quick response. Appreciate it, I have a follow-up question as I am still stuck.  When I do what you suggested in your response above and get the green light my PC indicates I am connected. But here  I am in  COINES environment and not in DD2 (GUI).  I wanted to run in DD2 environment and see the pressure/temp. chart  How do I, achieve that?  I followed your steps and got the green LED. but when I run the DD2 it cannot even connect to the board. If I update flash from DD2 after the Blue it just sit there. with Flash updating ...     Thank you
     
     
     
    jsayed
    New Poster

    Re: BMP390 - data is not displayed on Application board3/BMP390 shuttle board and DD2.

    Hi, someone, anyone PLEASE -- even a hint on my above question (previous remark)..... THANK YOU

    BSTRobin
    Community Moderator

    Re: BMP390 - data is not displayed on Application board3/BMP390 shuttle board and DD2.

    Hi jsayed,

    COINES environment didn't support to display GUI, you could see it from application note under "C:\COINES\v2.7.0\doc".

    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist