Bosch Sensortec Community

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    BNO055 power on reset issues

    New Poster

    BNO055 power on reset issues

    I'm trying to resolve a persistent issue I'm having with a BNO055 IMU on a custom PCBA. I'm communicating via I2C and am experiencing different behavior between device reset (using "Power on Reset" reset pin) with and without power cycling. In situations where I reprogram my MCU and start directly into my application code without power cycling, the IMU will respond with NAKs to any and all read/write messages. If I power-cycle the system, it works correctly. In both scenarios I'm pulling the reset pin low for ~25ms, pulling the reset pin high, and then waiting for ~725ms before initiating I2C communication. All other signals (COM1, COM2, PS0, PS1, nBOOT_LOAD_PIN) are connected to VDD or GND directly or through a 10kΩ resistor. A partial schematic is attached.

    The firmware is heavily based upon the BNO055 XPlained Pro example code and is being run on a SAMD21G18A.

    Can you help me to understand the differences in behavior between device reset for the BNO055 from an 'unknown' state and from a power-on state? Do I need to set the SDA/SCL lines to a certain level before/during/after Power on Reset?

    Attached are logic analyzer screenshots of the system failing without power cycle (BNO055_noPowerCycle.png) and working with power cycle (BNO055_withPowerCycle.png), as well as a partial schematic (BNO055_sch.png).

    15 REPLIES 15
    New Poster

    Re: BNO055 power on reset issues

    I've tried bit-banging an empty I2C frame in case an I2C transmission was interrupted by the MCU being reprogrammed (the clumsy approach here: i2c-bus.org) but haven't seen any improvement from any number of clock pulses - 8, 9, 10, 16, 32.

    Community Moderator

    Re: BNO055 power on reset issues

    Can you leave a email address since we need some additional information for this issue

    Highlighted
    Occasional Visitor

    Re: BNO055 power on reset issues

    I too am seeing this issue, the BNO055 works fine on on a power cycle, but issuing a reset by I2C seems to lock up the sensor.
    Did you get this to work with help from Bosch? Thanks for any help in advance.

    Community Moderator
    Community Moderator

    Re: BNO055 power on reset issues

    Hi chrisc and brentpop,

     

    We recently discovered a bug in the reset process when the BNO055 expects a crystal to be connected. This means that the BNO055 will fail to reset if there is no external crystal attached.

     

    To prevent the issue:

    1. If possible, use an external crystal;
    2. If 1 is not possible, avoid triggering a reset after the part has been turned on.

     

    Current workaround:

    • Until a new firmware is provided, to reset the BNO055 to a known state, write every configuration register to a known value of your choice, such as the default value (or other).

     

    Future fix:

    • Fixing this issue in the field will require a firmware update to the BNO055 pre-programmed firmware. For this, it will require the host MCU to have a connection to the nBOOT_LOAD_PIN in order to enter the bootloader. More details on the firmware update protocol will be disclosed when the new firmware is available.
    • It is also possible, but not guaranteed, that future BNO055 will be pre-programmed with the fixed version fo the software.
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist