About IPShiv

Good day! I have problems with BSEC library. I can geet raw values from sensor, but all others (CO2, IAQ, VOC) always stay constant. I use built-in nRF SDK's scheduler to control delays, so I rewrited iot example from BSEC library. First of all I initiate sensor   new_bme680.dev_id = BME680_I2C_ADDR_PRIMARY; new_bme680.intf = BME680_I2C_INTF; new_bme680.read = i2c_read_reg; new_bme680.write = i2c_write_reg; new_bme680.delay_ms = nrf_delay_ms; /* amb_temp can be set to 25 prior to configuring the gas sensor * or by performing a few temperature readings without operating the gas sensor. */ new_bme680.amb_temp = 25; int8_t rslt = BME680_OK; rslt = bme680_init(&new_bme680); if (rslt != BME680_OK) { __LOG(LOG_SRC_APP, LOG_LEVEL_INFO, "BME INIT STATUS %d\n", rslt); return false; } bsec_library_return_t bsec_status; bsec_status = bsec_init(); if (rslt != BSEC_OK) { __LOG(LOG_SRC_APP, LOG_LEVEL_INFO, "BSEC INIT STATUS %d\n", rslt); return false; } /* Set the temperature, pressure and humidity settings */ new_bme680.tph_sett.os_hum = BME680_OS_1X; new_bme680.tph_sett.os_pres = BME680_OS_16X; new_bme680.tph_sett.os_temp = BME680_OS_2X; new_bme680.tph_sett.filter = BME680_FILTER_SIZE_3; /* Set the remaining gas sensor settings and link the heating profile */ new_bme680.gas_sett.run_gas = BME680_ENABLE_GAS_MEAS; /* Create a ramp heat waveform in 3 steps */ new_bme680.gas_sett.heatr_temp = 320; /* degree Celsius */ new_bme680.gas_sett.heatr_dur = 150; /* milliseconds */     After that update subscription and setup sensor   requested_virtual_sensors[0].sensor_id = BSEC_OUTPUT_IAQ; requested_virtual_sensors[0].sample_rate = sample_rate; requested_virtual_sensors[1].sensor_id = BSEC_OUTPUT_STATIC_IAQ; requested_virtual_sensors[1].sample_rate = sample_rate; requested_virtual_sensors[2].sensor_id = BSEC_OUTPUT_CO2_EQUIVALENT; requested_virtual_sensors[2].sample_rate = sample_rate; requested_virtual_sensors[3].sensor_id = BSEC_OUTPUT_BREATH_VOC_EQUIVALENT; requested_virtual_sensors[3].sample_rate = sample_rate; requested_virtual_sensors[4].sensor_id = BSEC_OUTPUT_RAW_TEMPERATURE; requested_virtual_sensors[4].sample_rate = sample_rate; requested_virtual_sensors[5].sensor_id = BSEC_OUTPUT_RAW_PRESSURE; requested_virtual_sensors[5].sample_rate = sample_rate; requested_virtual_sensors[6].sensor_id = BSEC_OUTPUT_RAW_HUMIDITY; requested_virtual_sensors[6].sample_rate = sample_rate; requested_virtual_sensors[7].sensor_id = BSEC_OUTPUT_RAW_GAS; requested_virtual_sensors[7].sample_rate = sample_rate; requested_virtual_sensors[8].sensor_id = BSEC_OUTPUT_SENSOR_HEAT_COMPENSATED_TEMPERATURE; requested_virtual_sensors[8].sample_rate = sample_rate; requested_virtual_sensors[9].sensor_id = BSEC_OUTPUT_SENSOR_HEAT_COMPENSATED_HUMIDITY; requested_virtual_sensors[9].sample_rate = sample_rate; requested_virtual_sensors[10].sensor_id = BSEC_OUTPUT_GAS_PERCENTAGE; requested_virtual_sensors[10].sample_rate = sample_rate; /* Call bsec_update_subscription() to enable/disable the requested virtual sensors */ status = bsec_update_subscription(requested_virtual_sensors, n_requested_virtual_sensors, required_sensor_settings, &n_required_sensor_settings); /* Select the power mode */ /* Must be set before writing the sensor configuration */ new_bme680.power_mode = BME680_FORCED_MODE; /* Set the required sensor settings needed */ uint8_t set_required_settings; set_required_settings = BME680_OST_SEL | BME680_OSP_SEL | BME680_OSH_SEL | BME680_FILTER_SEL | BME680_GAS_SENSOR_SEL; /* Set the desired sensor configuration */ rslt = bme680_set_sensor_settings(set_required_settings,&new_bme680); /* Set the power mode */ rslt = bme680_set_sensor_mode(&new_bme680);     And when scheduler starts I request measurment   time_stamp = (int64_t)app_timer_cnt_get()*1000; bsec_library_return_t status = bsec_sensor_control(0, &sensor_settings); bme680_bsec_trigger_measurement(&sensor_settings); uint8_t num_bsec_inputs = 0; bme680_bsec_read_data(time_stamp, bsec_inputs, &num_bsec_inputs, sensor_settings.process_data); bme680_bsec_process_data(bsec_inputs, num_bsec_inputs);     As a result I receive raw data from sensor and constat data iaq:25, co2:500, voc:0 from bsec algorithms. Question is what am I doing wrong? ... View more