Subject | Author | Likes | Latest Post | Replies | |
---|---|---|---|---|---|
Which BSEC output should I use for my application ? I am not sure what is the difference between IA...
| 2 | 1 | |||
In BME680 datasheet, there are formulas to convert the raw data into temperature, pressure, relativ...
| 2 | 4 | |||
Hello, New to the forum. I'm wordering if there exists any official Allan deviation plot for BMI1...
| 0 | 2 | |||
BSEC outputs an 'IAQ accuracy' together with the IAQ output, but what do values from 0 to 3 mean?
| 2 | 1 | |||
What is the Bosch Sensortec date code policy?
|
Anonymous
| 2 | 3 | ||
My COINES example does not show printf output anymore, only after closing... - ( 01-24-2019 11:02 AM )
I have modified the example bmi160_read_sensor_data.c, but now the output is gone. The output only ...
| 1 | 2 | |||
Where can I find documentation about sensor placement and HW PCB design with Bosch Sensortec sensor...
| 2 | 1 | |||
How to get access to the drivers for different type of plaforms
| 0 | 1 | |||
I need some help to find the right sensor for my application, do you have any documents that provid...
| 0 | 1 | |||
can you please explain how to compensate temperature effects (e.g TCO) during our manufacturing pro...
| 0 | 1 | |||
We have built a platform using the BMM150 and we are trying to get the +/-2.5 deg of heading error ...
| 0 | 1 | |||
I need absolute orientation output in my device, what's the difference between BNO055 and ... - ( 12-20-2018 02:54 PM )
I need absolute orientation output in my device. I see you have several options available like the ...
| 0 | 1 | |||
What does accuracy values between 0 and 3 mean for each output (accelerometer, gyroscope, magnetome...
| 0 | 1 | |||
When I rotate the sensor, I see heading jumps and discontinuities, is it the expected behavior ?
| 1 | 1 | |||
Can you please recommend a sensor module with connectivity?
| 0 | 3 | |||
How to compensate [temperature, pressure, humidity] data obtained from [BMP, BME]? - ( 12-19-2018 01:43 PM )
Do you have API to compensate temperature, pressure... data measurements from BMP and BME sensors
| 0 | 1 | |||
How can we get real-time sea level pressure value?
| 1 | 1 | |||
can you please explain how to get altitude measurement from pressure data from the sensor
| 0 | 12 | |||
Can you please explain why we need a dummy SPI after switching to SPI protocol? and What is the min...
| 0 | 1 | |||
Why the temperature and pressure measurements from BMPx or BMEx are always constant? - ( 12-19-2018 12:35 PM )
When I power on the BMPx or BMEx sensors I get constant measurements of temperature and pressure, c...
| 0 | 2 | |||
After a soft-reset, sometimes the I2C communication in BNO055 doesn't work, can you please help?
| 0 | 1 | |||
I'm interested to evaluate the BNO055 smart sensors, can you recommend available boards for this se...
| 0 | 1 | |||
Can you please explain the BMI160 accelerometer low power mode and how does it work?
| 0 | 1 | |||
BMI160 has primary I2C/SPI interface. It also has secondary I2C interface for external magnetometer...
| 0 | 1 | |||
Can an external magnetometer connect to BMI160 via secondary I2C interface. Does it support only Bo...
| 0 | 1 | |||
What is the ODR on BMI160 secondary interface?
| 0 | 1 | |||
Pull up or pull down register when the BMI160 INT pin is configured to open drain? - ( 12-18-2018 01:20 PM )
How to use the Pull up / pull down register when the sensor INT pin is configured to open drain?
| 0 | 1 | |||
Why there is data missing in the FIFO when changing the ODR / bandwidth of the sensor on-the-fly?
| 1 | 1 | |||
What is the maximum SPI clock speed supported by the BMI160 secondary interface?
| 0 | 1 | |||
I would like to know what's the use of the SPI dummy read in BMI160, and What is the minimum delay ...
| 0 | 2 |